DIY Bath Setup.
DIY Bath Setup.
Blog Article
The content in the next paragraphs about A Step-by-Step Guide to Installing a Bathtub is incredibly engaging. Give it a try and make your own conclusions.
Setting up a bathtub isn't specifically rocket science, yet it does need solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably difficult job. If the old bathtub is conveniently easily accessible, the job can relocate immediately; if you have to open up a wall surface to remove the old bathtub and position the brand-new tub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will certainly need an assistant to move out the old tub and embeded in the new one. Make certain you have qualified yourself for the job as well as are comfortable trying it. Rather than hiring a contractor to take control of a halfway-completed task, it is better to consider using one before you start. Chances are you might require a professional plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have currently acquired a brand-new bathtub and don't require to change the arrangement of your previous water system pipes.
Your devices and also product list should consist of the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any type of water staying in the system. The procedure of removing the existing taps can be rather problematic because of the limited gain access to that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipelines. As soon as the supply pipelines have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin making sure that the washers are in place in between the tap and also the sink. Secure the faucet in place with the manufacturer given backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The former kind ought to be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 small points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub till the level reads degree.
To install taps, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; then do the same for the various other faucet.
Switch on the water and also check all joints as well as new pipework for leakages and also tighten them if needed. Load the bathtub and additionally examine the overflow outlet as well as the regular outlet for leakages.
Lastly, deal with the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has actually been used at least when as this will certainly resolve it into its last position.
Planning for the Installation
Firstly, the supporting structure provided with the bathroom must be fitted (if required) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to avoid strain on the tub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you make use of every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last setting.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom and the tiling, leading to difficulties with dampness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also can securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealant can split fairly early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading up on A Step-by-Step Guide to Installing a Bathtub? Leave a short review down below. We'd be glad to find out your thinking about this blog post. In hopes to see you back again soon. Sharing is good. One never knows, you may just be helping someone out. We appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book An Estimate Now Report this page